Comprehensive Product Summary – SWM‑04GF‑SS‑ST_4 (Module 4×1000FX ST SS IEC‑61850)

---

### 1. Product Overview

Product Name: SWM‑04GF‑SS‑ST_4
Article Number: SWM‑04GF‑SS‑ST_4
Description: Module 4×1000FX ST SS IEC‑61850
Series: RGS‑9000 Series – Industrial Managed Ethernet Switch
Manufacturer: ORing Industrial Networking Corp.
Website: [www.oring-networking.com](http://www.oring-networking.com)
Contact:
- Tel: +886‑2‑2918‑1066
- Fax: +886‑2‑2918‑2368
- Email: support@oring-networking.com

The SWM‑04GF‑SS‑ST_4 is a modular fiber interface card designed for the RGS‑9000 Series of industrial managed Ethernet switches. It provides four 1000Base‑FX single‑mode fiber ports using ST connectors, supporting transmission distances up to 30 km. The module is fully compliant with IEC 61850‑3 and IEEE 1613 standards for power substation and railway applications, ensuring high reliability under harsh environmental conditions.

---

### 2. Key Features

- Four 1000Base‑FX Single‑Mode Fiber Ports:
Each port supports up to 1 Gbps full‑duplex operation over single‑mode fiber with ST connectors.
- Long‑Distance Transmission:
Optical reach up to 30 km per port using standard single‑mode fiber.
- Industrial‑Grade Design:
Compliant with IEC 61850‑3 and IEEE 1613 for electromagnetic immunity, surge protection, and temperature endurance.
- Extended Operating Temperature:
Rated for –40 °C to +70 °C, suitable for outdoor and substation environments.
- Hot‑Swappable Modular Architecture:
Designed for the RGS‑9000 chassis, allowing field replacement or expansion without system downtime.
- O‑Ring Redundancy Support:
Integrates with ORing’s proprietary O‑Ring and O‑Chain redundancy protocols, providing recovery times under 30 ms across up to 250 nodes.
- SFP+ Compatibility:
Supports fiber SFP/SFP+ modules for flexible deployment.
- High Immunity and Reliability:
Meets IEC 61000‑4‑2/3/4/5/6/8/11 EMC standards; resistant to ESD, surge, and EFT disturbances.
- Centralized Management:
Fully manageable through the RGS‑9000’s web interface, CLI, SNMP, and Open‑Vision utility.
- Energy‑Efficient Ethernet:
Supports IEEE 802.3az for reduced power consumption during low traffic periods.

---

### 3. Technical Specifications

| Parameter | Specification |
|----------------|------------------|
| Interface Type | 4 × 1000Base‑FX single‑mode fiber |
| Connector Type | ST |
| Transmission Distance | Up to 30 km |
| Optical Wavelength | 1310 nm (typical) |
| Fiber Type | Single‑mode, 9/125 µm |
| Data Rate | 1 Gbps full‑duplex per port |
| Module Form Factor | Plug‑in module for RGS‑9000 chassis |
| Operating Temperature | –40 °C to +70 °C |
| Storage Temperature | –40 °C to +85 °C |
| Humidity | 5 % – 95 %, non‑condensing |
| Compliance | IEC 61850‑3, IEEE 1613, EN61000‑4‑2/3/4/5/6/8/11 |
| Dimensions (chassis) | 440 (W) × 325 (D) × 44 (H) mm (1U rack‑mount) |
| Weight (chassis) | Approx. 6.45 – 6.6 kg depending on configuration |
| Power Supply (via chassis) | Dual redundant modular AC/DC inputs (12 V DC internal bus) |
| Power Consumption (typ.) | < 50 W for full chassis with modules |
| Cooling | Passive convection, no moving parts |
| Enclosure | 19‑inch rack‑mountable metal housing |

---

### 4. Functionality

The SWM‑04GF‑SS‑ST_4 module functions as a fiber uplink interface for the RGS‑9000 Series managed switches. It converts electrical Ethernet signals from the switch backplane into optical signals for long‑distance transmission.

Operation Principle:
- Each port operates as a 1000Base‑FX interface, transmitting and receiving optical signals over single‑mode fiber.
- The module connects directly to the RGS‑9000’s internal switching fabric, enabling full Layer 2/3 managed functionality including VLANs, QoS, redundancy, and routing.
- Supports auto‑negotiation, link fault detection, and loop protection through the host switch firmware.

Typical Applications:
- Power substation automation networks (IEC 61850‑3 compliant).
- Railway and rolling‑stock communication systems.
- Industrial process control and SCADA backbones.
- Long‑distance fiber uplinks between substations or control centers.
- Redundant ring or chain topologies for mission‑critical Ethernet networks.

Compatibility:
- Fully compatible with RGS‑9000, RGS‑P9000, and RGS‑PR9000 chassis.
- Interoperable with standard Ethernet devices supporting 1000Base‑FX.
- Supports integration with third‑party ring protocols via Open‑Ring and MRP (IEC 62439‑2).

---

### 5. Components & Accessories

Included Items (with RGS‑9000 chassis):
- SWM‑04GF‑SS‑ST_4 fiber module (factory‑installed or field‑installable).
- Console cable (DB‑9 to RJ‑45) for management.
- Rack‑mount kit (L & R brackets, M3 screws).
- Power cords (AC or DC type depending on model).
- Quick Installation Guide and documentation CD.

Optional Accessories:
- Additional fiber modules (e.g., SWM‑04GF‑MM‑SC, SWM‑04GF‑SS‑LC).
- RJ‑45 copper modules (SWM‑08GT, SWM‑08GP).
- 10 G SFP+ modules (SWM‑04GP+).
- Redundant power modules (AC or DC).
- SFP/SFP+ transceivers for various wavelengths and distances.

Connectors:
- ST optical connectors for each fiber port.
- Backplane edge connector for data and power interface to chassis.

---

### 6. Installation & Setup

Installation Requirements:
- Compatible RGS‑9000 Series chassis with available module slot (Slot 1–3).
- Power off the chassis before inserting or removing modules.
- Observe ESD precautions when handling optical modules.

Installation Steps:
1. Turn off the RGS‑9000 power supply.
2. Remove the blank panel from the desired slot.
3. Insert the SWM‑04GF‑SS‑ST_4 module firmly into the slot until it seats into the backplane connector.
4. Secure the module with retaining screws.
5. Re‑apply power to the chassis.
6. Verify module recognition via front‑panel LEDs or web interface.

Configuration:
- Access the switch via web browser (default IP 192.168.10.1, user admin/admin).
- Configure port parameters, VLANs, redundancy, and QoS as required.
- Use Open‑Vision utility or CLI for advanced management.

Mounting Options:
- Standard 19‑inch rack mounting (1U height).
- Dual redundant power modules can be installed in dedicated power slots.

---

### 7. Performance & Capabilities

Network Performance:
- Switching Bandwidth: 128 Gbps (chassis).
- Switching Latency: < 7 µs.
- MAC Table: 8 K – 32 K entries depending on model.
- Packet Buffer: 32 Mbit.
- Jumbo Frame Support: Up to 9.6 K bytes.
- Priority Queues: 8 hardware queues per port.

Redundancy & Recovery:
- O‑Ring: < 30 ms recovery over 250 nodes.
- O‑Chain: Multi‑ring interconnection for large‑scale redundancy.
- MRP (IEC 62439‑2): Recovery < 80 ms for 50 devices.
- MSTP/RSTP/STP: IEEE 802.1s/w/D compliant.
- VRRP/RIP/Static Routing: Supported on Layer 3 models (RGS‑PR9000).

Security & Management:
- Authentication: 802.1X, RADIUS, TACACS+, local user database.
- Encryption: HTTPS, SSH, SNMPv3.
- Access Control: ACLs, device binding, DoS/DDoS prevention.
- Network Management: SNMP v1/v2c/v3, LLDP, Modbus TCP, Open‑Vision utility.
- Diagnostics: Cable diagnostics, SFP monitoring (DDM), temperature sensors.

Environmental Performance:
- Operating Temperature: –40 °C to +70 °C (module); chassis up to +85 °C without 10 G module.
- Storage Temperature: –40 °C to +85 °C.
- Humidity: 5 % – 95 %, non‑condensing.
- Shock/Vibration: IEC 60068‑2‑27/‑2‑6 compliant.

Limitations:
- Module requires RGS‑9000 chassis; not standalone.
- Optical reach depends on fiber quality and connector cleanliness.
- 10 G SFP+ modules reduce maximum ambient temperature to +60 °C.

---

### 8. Standards & Compliance

Industrial and Environmental Standards:
- IEC 61850‑3: Power automation and substation communication.
- IEEE 1613: Environmental and EMI standards for electric power substations.
- EN 50155 / EN 50121‑3‑2 / EN 50121‑4: Railway and rolling‑stock compliance.
- EN 61000‑4‑2/3/4/5/6/8/11: EMC immunity (ESD, RS, EFT, Surge, CS, Power frequency).
- FCC Part 15 Class A / CISPR 22 Class A: EMI emission compliance.
- EN 60950‑1: Safety standard for IT equipment.

Ethernet & Protocol Standards:
- IEEE 802.3 (10Base‑T), 802.3u (100Base‑TX/FX), 802.3ab (1000Base‑T), 802.3z (1000Base‑X).
- IEEE 802.3ae (10 Gigabit Ethernet).
- IEEE 802.3x (Flow Control).
- IEEE 802.3ad (LACP).
- IEEE 802.1p (QoS/CoS).
- IEEE 802.1Q (VLAN Tagging).
- IEEE 802.1w/s (RSTP/MSTP).
- IEEE 802.1x (Port‑based Authentication).
- IEEE 802.1AB (LLDP).
- IEEE 1588v2 (Precision Time Protocol).
- IEC 62439‑2 (MRP).

Certifications:
- CE, FCC, RoHS, and UL‑recognized components.
- Designed for long‑term operation in high‑EMI industrial environments.

---

### 9. Additional Information

Warranty:
- 5‑year limited warranty covering defects in materials and workmanship.
- Excludes damage due to misuse, improper installation, or unauthorized modification.

Technical Support:
- Email: support@oring-networking.com
- Online resources: firmware updates, manuals, and Open‑Vision management software.

Maintenance:
- Periodically inspect fiber connectors for dust or contamination.
- Ensure adequate ventilation in rack installations.
- Firmware updates available via web interface or CLI (TFTP/HTTP).

Firmware & Configuration Management:
- Supports configuration backup/restore in XML format.
- Remote firmware upgrade via web or CLI.
- SNMP traps, Syslog, and SMTP event notifications for system monitoring.

Safety & Handling:
- Observe ESD precautions when handling optical modules.
- Disconnect power before module insertion or removal.
- Use only ORing‑approved power modules and accessories.

---

### Summary

The SWM‑04GF‑SS‑ST_4 is a high‑reliability 4‑port 1000Base‑FX single‑mode fiber module engineered for the RGS‑9000 Series industrial managed Ethernet switches. It delivers long‑distance optical connectivity (up to 30 km) with ST connectors, ensuring robust communication in power substations, railway systems, and other mission‑critical industrial networks.

With compliance to IEC 61850‑3 and IEEE 1613, extended temperature tolerance (–40 °C to +70 °C), and integration with ORing’s O‑Ring redundancy technology, the module provides exceptional resilience and uptime. Combined with the RGS‑9000’s advanced Layer 2/3 management, QoS, security, and synchronization features, it forms a scalable, standards‑based platform for industrial Ethernet backbones requiring deterministic performance and high availability.

---

End of Product Summary – SWM‑04GF‑SS‑ST_4 (Module 4×1000FX ST SS IEC‑61850)