- **Dual Redundant Ethernet Ports:** Two 10/100Base‑T(X) ports support redundant or switch (daisy‑chain) mode with automatic recovery time under 10 ms, ensuring continuous network connectivity. - **PoE PD Support (IEEE 802.3af):** The ETH2 port functions as a Power‑over‑Ethernet Powered Device (PD) with 1 kV isolation, allowing flexible power sourcing and simplified cabling. - **Multi‑Protocol Serial Connectivity:** Four configurable serial ports supporting RS‑232, RS‑422, and 2‑ or 4‑wire RS‑485 interfaces, selectable via software (DS‑Tool). - **Redundant Power Inputs:** Dual 12–48 V DC inputs via terminal block and DC jack, with reverse polarity protection and fault relay output (1 A @ 24 V DC). - **High Reliability and Rugged Design:** IP‑30 metal housing, DIN‑rail or wall‑mount installation, and compliance with IEC 60068 shock, vibration, and free‑fall standards. - **Advanced Redundancy and Failover:** Automatic LAN failover (

Manufacturer: Oring

Category: Industrial Device Server

- **Dual Redundant Ethernet Ports:** Two 10/100Base-T(X) RJ-45 ports support redundant or switch (daisy-chain) mode with automatic recovery time under 10 ms, ensuring continuous network connectivity. - **Four Isolated Serial Ports:** 4× RS-422/485 ports with 2 kV DC isolation for reliable communication in electrically noisy environments. - **PoE PD Support:** ETH2 port supports IEEE 802.3af Power over Ethernet (PD) with 1 kV isolation and up to 8 W power draw. - **Redundant Power Inputs:** Dual 12–48 VDC inputs via terminal block and DC jack for power redundancy. - **Multiple Host Connections:** Supports up to 5 simultaneous host connections in Virtual COM, TCP Server, TCP Client, or UDP modes. - **Secure Management:** HTTPS and SSH protocols for encrypted configuration and monitoring. - **Event Notification:** Alerts via Syslog, Email, SNMP trap, relay output, or beeper for system events and faults. - **NAT Pass-Through:** Enables remote management through NAT routers, simplifying access across different IP domains. - **Software Utility (DS-Tool):** Windows-based configuration and monitoring utility for device discovery, group management, and firmware updates. - **Industrial Design:** IP30-rated metal housing, DIN-rail and wall-mount options, and wide operating temperature range (-10°C to 60°C). - **Comprehensive Protocol Support:** TCP/IP, UDP, DHCP, BOOTP, ARP/RARP, DNS, SNMP MIB II, HTTPS, SSH.

Manufacturer: Oring

Category: Industrial Device Server

- **Dual Redundant Ethernet Ports:** Two 10/100Base-T(X) ports with recovery time under 10 ms for network redundancy or daisy-chain switch mode. - **Wireless Connectivity:** IEEE 802.11b/g WLAN interface supporting up to 54 Mbps link speed. - **High Security:** Supports WEP (64/128-bit), WPA, WPA2, TKIP, AES encryption, and 802.1X authentication. - **Multiple Serial Interfaces:** Four isolated RS-422/485 ports with 2 kV DC isolation for industrial noise immunity. - **Redundant Power Inputs:** Dual 12–48 VDC inputs on terminal block with reverse polarity protection. - **Multi-Host Communication:** Supports up to five simultaneous host connections in Virtual COM, TCP Server, TCP Client, or UDP modes. - **Event Notification:** Alerts via Syslog, Email, SNMP trap, relay output, or beeper for fault and status events. - **Secure Management:** HTTPS and SSH protocols for encrypted configuration and monitoring. - **NAT Pass-Through:** Enables remote management through NAT routers across different IP domains. - **Flexible Configuration:** Managed via DS-Tool Windows utility, web browser, or SSH console. - **Industrial Design:** IP30-rated metal housing, DIN-rail and wall-mount options, and wide operating temperature range (-10°C to 55°C). - **Software Compatibility:** Supports Windows NT/2000/XP/2003/Vista (32-bit) for Virtual COM and DS-Tool utilities.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi‑Interface Serial Connectivity:** Four configurable RS‑232/422/485 ports supporting 2‑wire or 4‑wire RS‑485 operation. - **Wireless LAN Integration:** IEEE 802.11b/g WLAN client mode with data rates up to 54 Mbps. - **Dual Redundant Ethernet Ports:** Two 10/100Base‑T(X) ports supporting redundant or switch (daisy‑chain) mode with recovery time

Manufacturer: Oring

Category: Industrial Device Server

- **Secure Serial-to-WLAN Connectivity:** Converts one RS232/422/485 serial port to a wireless 802.11b/g network interface, enabling legacy serial devices to communicate over modern wireless infrastructure. - **High-Speed Wireless Performance:** Supports WLAN link speeds up to 54 Mbps with IEEE 802.11b/g dual-mode operation. - **Advanced Data Security:** Implements SSL encryption for secure data transfer, HTTPS and SSH for management, and supports WEP, WPA, WPA2, TKIP, and 802.1X authentication protocols. - **Multiple Host Redundancy:** Allows up to five simultaneous host connections in Virtual COM, TCP Server, TCP Client, or UDP modes, ensuring data redundancy and reliability. - **NAT Pass-Through:** Enables remote management and communication through NAT routers, simplifying deployment across different IP domains. - **Dual Power Inputs:** Redundant 12–48 VDC power inputs via both a 3-pin terminal block and a DC power jack for uninterrupted operation. - **Flexible Configuration:** Configurable via web-based interface, Windows utility (DS-Tool), or console command line. - **Event Notification System:** Supports Syslog, email alerts, SNMP traps, and audible beeper alarms for proactive fault management. - **Industrial-Grade Design:** Compact IP30-rated metal housing suitable for DIN-rail or wall mounting, designed for harsh industrial environments. - **Wide OS Compatibility:** Supports Windows NT, 2000, XP, 2003, and Vista (32-bit) operating systems for Virtual COM driver and DS-Tool management utility.

Manufacturer: Oring

Category: Industrial Device Server

- **Secure Serial‑to‑Fiber Conversion:** Converts one RS‑232/422/485 serial port to one 100Base‑FX multimode fiber Ethernet port, enabling long‑distance, interference‑free communication. - **Data Security via SSL Encryption:** Supports **SSL encryption** to ensure secure data transmission between serial devices and Ethernet networks, protecting sensitive industrial data from interception or tampering. - **Redundant Host Connectivity:** Allows **simultaneous connection to up to five host PCs** in Virtual COM, TCP Server, TCP Client, or UDP modes. This redundancy ensures continuous data availability even if one host fails. - **Network Redundancy and Fast Recovery:** Incorporates **Ethernet redundancy** with recovery times of less than **10 ms**, minimizing downtime in case of network interruptions. - **Dual Power Inputs:** Features **redundant 12–48 VDC power inputs** via both a DC terminal block and a DC power jack, ensuring uninterrupted operation during power source failure. - **Comprehensive Event Warning System:** Supports event notifications through **Syslog, Email, SNMP Trap, Relay output, and Beeper**, allowing proactive monitoring and fault management. - **Secure Management Interfaces:** Provides **HTTPS and SSH** for encrypted configuration sessions, along with **console command control** for direct management. - **NAT Pass‑Through and DDNS Support:** Enables remote management through NAT routers and supports **Dynamic DNS (DDNS)** for flexible domain‑based access. - **PPPoE Connectivity:** Supports **Point‑to‑Point Protocol over Ethernet (PPPoE)** for integration into broadband or ISP‑based networks. - **Versatile Operation Modes:** Operates in **Virtual COM, Serial Tunnel, TCP Server, TCP Client, and UDP** modes, offering flexibility for various communication architectures. - **Industrial‑Grade Design:** Constructed with a **metal IP‑30 rated housing**, suitable for harsh industrial environments. Supports **DIN‑rail and wall mounting** for flexible installation. - **Software Utility – DS‑Tool:** Bundled with **DS‑Tool**, a Windows‑based management utility for configuration, monitoring, and firmware updates across multiple ORing device servers.

Manufacturer: Oring

Category: Industrial Device Server

- **Secure Serial‑to‑Fiber Conversion:** Converts one RS‑232/422/485 serial port to one 100FX single‑mode fiber Ethernet port, enabling long‑distance, interference‑free communication. - **Data Security with SSL Encryption:** Ensures confidentiality and integrity of transmitted data using SSL encryption, protecting against unauthorized access and data interception. - **Redundant Multi‑Host Connectivity:** Supports up to **five simultaneous host connections** in Virtual COM, TCP Server, TCP Client, or UDP modes, providing communication redundancy and failover capability. - **Network Redundancy and Fast Recovery:** Ethernet redundancy with recovery time of **less than 10 ms**, ensuring continuous operation in case of network link failure. - **Comprehensive Event Notification:** Supports event warnings via **Syslog, Email, SNMP Trap, Relay output, and Beeper**, allowing proactive system monitoring and fault management. - **Secure Management Interfaces:** Configuration and management via **HTTPS, SSH, and Console** interfaces, ensuring secure remote administration. - **NAT Pass‑Through and DDNS Support:** Enables device management across different IP domains and through NAT routers, simplifying remote access and deployment. - **PPPoE Support:** Allows direct Internet connectivity for remote applications without requiring additional network infrastructure. - **Dual Redundant Power Inputs:** Accepts **12–48 VDC** through both a terminal block and a DC power jack, ensuring uninterrupted operation during power source failure. - **Industrial‑Grade Design:** Rugged **IP‑30 metal housing**, compact form factor, and **DIN‑rail or wall‑mount** installation options for flexible deployment in harsh industrial environments. - **Comprehensive OS Support:** Compatible with **Windows NT/2000/XP/2003/Vista (32‑bit)** operating systems, with fixed TTY driver support for Linux. - **Configuration Utility – DS‑Tool:** ORing’s Windows‑based DS‑Tool utility simplifies configuration, monitoring, and management of multiple device servers across an industrial network.

Manufacturer: Oring

Category: Industrial Device Server

- **Redundant Dual Ethernet Ports:** Two 10/100Base‑TX LAN ports with automatic failover and recovery time of less than 10 ms ensure uninterrupted network communication. - **Secure Data Transmission:** SSL encryption for TCP Server and TCP Client modes guarantees secure data transfer across Ethernet networks. - **Multiple Host Redundancy:** Supports up to **five simultaneous host connections** in Virtual COM, TCP Server, TCP Client, or UDP modes, ensuring data availability even if one host fails. - **Versatile Operation Modes:** Configurable as Virtual COM, Serial Tunnel, TCP Server, TCP Client, or UDP for flexible integration with various industrial systems. - **Network Redundancy and Switch Mode:** Daisy‑chain (switch) mode reduces the need for additional Ethernet switches, simplifying network topology. - **Comprehensive Event Warning System:** Event notifications via Syslog, Email, SNMP Trap, Relay output, or Beeper alert operators to network or device anomalies. - **Secure Management Interfaces:** HTTPS and SSH protocols provide encrypted management sessions; console command control and DS‑Tool utility simplify configuration. - **NAT Pass‑Through:** Enables remote management through NAT routers, allowing access from different IP domains. - **Internet Connectivity:** Built‑in PPPoE and DDNS support for dynamic IP environments and remote access. - **Redundant Power Inputs:** Dual 12–48 V DC inputs via terminal block and power jack ensure continuous operation during power source failure. - **Industrial‑Grade Design:** IP‑30 metal housing, compact form factor, and DIN‑rail/panel mounting options for reliable deployment in industrial control cabinets. - **Cross‑Platform Support:** Compatible with Windows NT/2000/XP/2003/Vista (32‑bit) and Linux (fixed TTY driver).

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Protocol Serial Support:** Four configurable serial ports supporting RS232, RS422, and 4(2)-wire RS485 communication modes, selectable via ORing’s DS-Tool utility. - **Dual Ethernet Ports:** Two 10/100Base-T(X) RJ45 LAN interfaces for network redundancy or dual network connectivity. - **Secure Communication:** Supports SSL data encryption and secure management interfaces (HTTPS, SSH) to ensure data integrity and confidentiality. - **Redundant Power Inputs:** Dual 12–48 VDC power inputs via terminal block for uninterrupted operation in case of power source failure. - **Fast Ethernet Redundancy:** Ethernet redundancy with recovery time less than 10 ms using ORing’s O-Ring technology, ensuring continuous network availability. - **Comprehensive Event Notification:** Supports multiple alert mechanisms including Syslog, Email, SNMP Trap, relay output, and audible beeper alarms. - **Industrial-Grade Design:** Rugged IP-30 metal enclosure with DIN-rail or wall-mount installation options, designed for harsh industrial environments. - **Wide Compatibility:** Compatible with Windows NT/2000/XP/2003/Vista (32-bit) and Linux (via fixed TTY driver). - **Flexible Management:** Web-based HTTPS console, SSH console, and DS-Tool configuration utility for Windows platforms. - **High Reliability:** 5-year manufacturer warranty and compliance with major industrial EMC and safety standards.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Protocol Serial Support:** Four serial ports configurable as RS232, RS422, or 4(2)-wire RS485 via DS-Tool software utility. - **Dual Ethernet Ports:** Two 10/100Base-T(X) RJ45 LAN ports for network redundancy or dual network operation. - **PoE Capability:** ETH2 port supports PoE (Power over Ethernet) with a maximum power consumption of 8W. - **Redundant Power Inputs:** Dual 12–48VDC power inputs ensure uninterrupted operation in case of power source failure. - **Fast Network Recovery:** Ethernet redundancy with recovery time under 10ms using ORing’s O-Ring technology. - **Comprehensive Event Notification:** Supports Syslog, Email, SNMP Trap, Relay output, and Beeper alerts for system events. - **Secure Communication:** SSL data encryption and SSH management for secure data transmission and configuration. - **Fixed TTY Driver for Linux:** Provides stable serial port mapping for Linux-based systems. - **Industrial-Grade Design:** Rugged metal housing with IP-30 protection, suitable for harsh industrial environments. - **Flexible Mounting Options:** DIN-rail and wall-mount installation supported. - **Wide Operating Voltage Range:** Accepts 12–48VDC input, with a maximum power consumption of 7W. - **Compact Form Factor:** Space-efficient design for control cabinets and industrial enclosures. - **Comprehensive Management Tools:** Web-based HTTPS console, SSH console, and DS-Tool for Windows NT/2000/XP/Vista 32-bit. - **Multi-Host Connectivity:** Supports up to five simultaneous host connections via Virtual COM, TCP Server, TCP Client, or UDP modes. - **Long-Term Reliability:** Backed by a 5-year manufacturer warranty.

Manufacturer: Oring

Category: Industrial Device Server

- **Dual Redundant Ethernet Ports:** Two 10/100Base‑TX LAN ports support redundant operation with **recovery time

Manufacturer: Oring

Category: Industrial Device Server

- **Multi‑Interface Connectivity:** Supports **4 serial ports (RS‑422/485)** and **2 Ethernet LAN ports (10/100Base‑T(X))**, enabling simultaneous communication between multiple serial devices and Ethernet networks. - **Wireless LAN Integration:** Built‑in **IEEE 802.11b/g WLAN** interface for wireless connectivity, allowing flexible deployment in locations where cabling is impractical. - **High Availability and Redundancy:** Features **Ethernet redundancy** with **recovery time

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Interface Serial Connectivity:** Supports **4 serial ports** configurable as RS-232, RS-422, or RS-485 via **DB9 male connectors**, enabling flexible integration with a wide range of legacy and modern serial devices. - **Dual Ethernet Ports:** Equipped with **2 × 10/100Base-T(X) RJ45 LAN ports**, supporting Ethernet redundancy and fast recovery times (

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Protocol Serial Support:** Compatible with RS-232, RS-422, and 4(2)-wire RS-485 interfaces. - **Automatic Baud Rate Detection:** Supports baud rates from 50 bps up to 921.6 Kbps with auto-switching capability. - **Full-Duplex Communication:** Enables full-duplex data transmission for RS-232 and RS-422 modes. - **Fiber Connectivity:** 100Base-FX fiber port with SC connector; available in multi-mode (2 km) and single-mode (30 km) variants. - **Wide Power Input Range:** Dual redundant 12–48 VDC inputs via a 4-pin terminal block for reliable operation. - **Industrial Design:** IP-30-rated metal housing ensures durability in harsh industrial environments. - **Flexible Mounting:** Supports both DIN-rail and wall-mount installation options. - **Extended Temperature Range:** Operates reliably from -40°C to +70°C, suitable for outdoor or factory-floor applications. - **Low Power Consumption:** Typical power usage of only 1.8 W. - **Comprehensive LED Indicators:** Provides clear visual feedback for power, fiber link/activity, and serial port activity. - **DIP Switch Configuration:** Allows easy selection of RS-422/RS-485 mode, termination resistor, and RS-232 DTE/DCE mode. - **High EMC/EMI Immunity:** Certified to multiple industrial and maritime standards for electromagnetic compatibility and safety. - **Long MTBF and Warranty:** Designed for long-term reliability with a 5-year manufacturer warranty.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi‑protocol Serial Support:** Compatible with RS‑232, RS‑422, and 4‑wire or 2‑wire RS‑485 interfaces. - **Automatic Baud Rate Detection:** Supports baud rates from **50 bps to 921.6 Kbps**, automatically adjusting to the connected device. - **Full‑Duplex Transmission:** Enables full‑duplex communication for RS‑232 and RS‑422 modes. - **Fiber Connectivity:** Converts serial data to **100Base‑FX** optical signals via an **SC single‑mode** connector. - **Extended Fiber Reach:** Supports transmission distances up to **30 km** at **1310 nm** wavelength. - **Industrial Design:** IP‑30 rated metal housing with compact dimensions (26.1 × 70 × 95 mm) and lightweight (192 g). - **Wide Operating Range:** Operates reliably from **‑40°C to +70°C**, suitable for harsh industrial conditions. - **Flexible Power Input:** Dual redundant **12–48 VDC** power inputs on a 4‑pin terminal block with overload protection. - **LED Indicators:** Dedicated LEDs for power, fiber link/activity, and serial port link/activity for RS‑232 and RS‑422/485. - **Mounting Options:** Supports both **DIN‑rail** and **wall‑mount** installation. - **Ease of Configuration:** DIP switches for mode selection (RS‑422/RS‑485), termination resistor enable/disable, and RS‑232 DTE/DCE configuration. - **High Reliability:** Mean Time Between Failures (MTBF) designed for long‑term industrial operation; backed by a **5‑year warranty**.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Interface Serial Support:** One DB9 male port configurable for **RS-232, RS-422, or RS-485 (2-wire/4-wire)** operation via DIP switch. - **Fiber Connectivity:** One **SC-type multi-mode fiber port**, supporting up to **5 km transmission distance** at **850 nm wavelength**. - **Ring Mode Functionality:** Enables **redundant fiber ring topology** for enhanced network reliability. - Up to **32 nodes at 115.2 kbps** - **24 nodes at 230.4 kbps** - **11 nodes at 460.8 kbps** - **6 nodes at 921.6 kbps** - **Auto/Manual Baud Rate Selection:** Supports baud rates from **50 bps to 921.6 kbps** with automatic or manual configuration. - **Dual Power Inputs:** Redundant **12–48 VDC** inputs on a 4-pin terminal block for uninterrupted operation. - **Industrial-Grade Design:** - **IP30-rated metal housing** for mechanical protection. - **Extended temperature range (-40°C to +75°C)** for outdoor or factory-floor environments. - **Shock, vibration, and free-fall resistance** per IEC60068 standards. - **LED Indicators:** Provide real-time status for power, serial TX/RX activity, auto baud rate, and ring mode operation. - **Compact Form Factor:** Slim design (26.1 × 70 × 95 mm) for space-constrained installations. - **Low Power Consumption:** Typical consumption of **1.6 W**. - **Compliance:** Meets **FCC Part 15B**, **EN55032 Class B**, and **EN61000-4-x** EMC/EMS standards. - **Warranty:** Backed by a **5-year manufacturer warranty**.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Interface Serial Support:** One serial port configurable for **RS-232, RS-422, or RS-485 (2-wire/4-wire)** operation via DIP switch. - **Fiber Connectivity:** One **multi-mode fiber port** with **ST connector**, supporting up to **5 km transmission distance** at **850 nm** wavelength. - **Ring Mode Functionality:** Supports **fiber ring topology** for redundant communication paths. - Up to **32 nodes @ 115.2 kbps** - **24 nodes @ 230.4 kbps** - **11 nodes @ 460.8 kbps** - **6 nodes @ 921.6 kbps** - **Auto/Manual Baud Rate Switching:** Configurable baud rate from **50 bps to 921.6 kbps**, with automatic detection or manual setting. - **Dual Power Inputs:** Accepts **+12 to +48 VDC** on a **4-pin terminal block**, providing redundancy and protection against power failure. - **Industrial-Grade Design:** - **IP30-rated metal enclosure** - **DIN-rail and wall-mount options** - **Extended operating temperature range**: **-40°C to +75°C** - **LED Indicators:** Multiple LEDs for **power**, **serial TX/RX activity**, **auto baud rate**, and **ring mode status**. - **Low Power Consumption:** Typical consumption of **1.6 W**, with **2 A overload current protection**. - **High Reliability:** Designed for **shock, vibration, and free-fall resistance** per **IEC60068** standards. - **Modbus Conversion Support:** Compatible with **Modbus protocol conversion**, enabling integration into industrial automation systems.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Protocol Serial Support:** Supports **RS-232, RS-422, and RS-485 (2-wire/4-wire)** interfaces, selectable via DIP switch configuration. - **Fiber Ring Mode:** Enables **redundant ring topology** for enhanced network reliability. In ring mode, the converter can automatically recover communication paths in case of fiber link failure. - **High-Speed Serial Communication:** Operates at baud rates from **50 bps up to 921.6 Kbps**, with both **auto and manual baud rate selection**. - **Extended Distance via Fiber:** Converts serial data to optical signals for transmission up to **40 km** over single-mode fiber at **1310 nm** wavelength. - **Dual Power Inputs:** Accepts **+12 to +48 VDC** dual redundant power inputs via a 4-pin terminal block, ensuring continuous operation even if one power source fails. - **Industrial-Grade Design:** - **IP30-rated metal enclosure** for mechanical protection. - **Wide operating temperature range** from **-40°C to +75°C**. - **DIN-rail and wall-mount options** for flexible installation. - **LED Indicators:** Multiple LEDs provide real-time status for power, serial TX/RX activity, auto baud rate detection, and ring mode operation. - **Compact and Lightweight:** Slim form factor (26.1 × 70 × 95 mm) and weight of approximately 205 g for easy integration into control cabinets or panels. - **Compliance and Reliability:** Certified for **FCC Part 15B**, **EN55032 Class B**, and **IEC60068** mechanical tests for shock, vibration, and free fall.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Interface Serial Support:** One serial port configurable for **RS-232, RS-422, or RS-485 (2-wire or 4-wire)** operation via DIP switches. - **Fiber Connectivity:** One **single-mode fiber port** with **ST connector**, operating at **1310 nm** wavelength, supporting transmission distances up to **40 km**. - **Ring Mode Functionality:** Supports **fiber ring topology** for network redundancy. - Up to **32 nodes @ 115.2 kbps** - Up to **24 nodes @ 230.4 kbps** - Up to **11 nodes @ 460.8 kbps** - Up to **6 nodes @ 921.6 kbps** - **Wide Baud Rate Range:** Auto or manual baud rate selection from **50 bps to 921.6 kbps**. - **Industrial-Grade Design:** - **IP-30-rated metal housing** for mechanical protection. - **Extended temperature range** (-40°C to +75°C). - **Shock, vibration, and free-fall tested** per IEC60068 standards. - **Dual Power Inputs:** Redundant **12–48 VDC** power supply with **overload current protection (2 A)**. - **LED Indicators:** Multiple status LEDs for **power, serial TX/RX activity, auto baud rate, and ring mode** operation. - **Compact Form Factor:** Slim design (26.1 × 70 × 95 mm) suitable for space-constrained control cabinets. - **Ease of Configuration:** DIP switches for mode selection, ring enablement, and termination resistor settings. - **High Reliability:** Designed for continuous operation in industrial automation, transportation, and energy systems.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Protocol Serial Support:** Compatible with RS-232, RS-422, and RS-485 (2-wire or 4-wire) serial communication standards. - **Automatic Baud Rate Detection:** Supports baud rates from **50 bps to 921.6 Kbps**, with automatic switching for flexible integration. - **WDM Bi-Directional Fiber Transmission:** Utilizes **TX1310/RX1550 nm** wavelengths for single-fiber communication, reducing cabling requirements and installation costs. - **Extended Communication Distance:** Supports up to **40 km** transmission distance over single-mode fiber. - **Industrial-Grade Design:** IP30-rated metal enclosure with **-40°C to +75°C** operating temperature range for harsh environments. - **Dual Power Inputs:** Redundant **12–48 VDC** power supply inputs on a 4-pin terminal block for high reliability. - **Compact Form Factor:** Slim housing (26.1 × 70 × 95 mm) suitable for space-constrained control cabinets. - **Flexible Mounting Options:** Supports both **DIN-rail** and **wall-mount** installation. - **Comprehensive LED Indicators:** Provides visual status for power, data transmission (TX/RX), and auto baud rate detection. - **High EMC Immunity:** Complies with EN61000-4 series standards for ESD, surge, EFT, and conducted immunity. - **Low Power Consumption:** Typical power usage of **1.6 W**, ensuring energy efficiency. - **Long-Term Reliability:** Backed by a **5-year warranty** and designed for continuous industrial operation.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Protocol Serial Support:** Compatible with RS-232, RS-422, and RS-485 (2-wire and 4-wire) interfaces, selectable via DIP switch. - **Auto Baud Rate Detection:** Automatically adjusts baud rate from **50 bps to 921.6 Kbps**, supporting multiple data formats and communication speeds. - **WDM Bi-Directional Fiber Transmission:** Utilizes **TX 1550 nm / RX 1310 nm** wavelength configuration for the “R” model, enabling full-duplex data transmission over a single fiber strand up to **40 km**. - **Industrial-Grade Design:** Rugged **IP-30 metal housing** ensures durability in harsh environments. - **Wide Operating Temperature:** Functions reliably from **-40°C to +75°C**, suitable for outdoor and factory-floor applications. - **Flexible Power Input:** Dual redundant **12–48 VDC** power inputs on a 4-pin terminal block with overload protection (2 A). - **Low Power Consumption:** Typical consumption of **1.6 W**, optimizing energy efficiency. - **DIN-Rail and Wall Mounting:** Includes both mounting kits for flexible installation. - **LED Indicators:** Provides clear visual feedback for power, data transmission, and auto baud rate status. - **EMC and Environmental Compliance:** Meets multiple EN61000 and IEC60068 standards for electromagnetic immunity, vibration, and shock resistance. - **Extended Communication Distance:** Supports up to **40 km** over single-mode fiber, ideal for remote serial device connectivity. - **Long-Term Reliability:** Backed by a **5-year warranty** and designed for continuous industrial operation.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi‑Protocol Serial‑to‑Ethernet Conversion:** Supports RS‑232, RS‑422, and RS‑485 interfaces on eight RJ‑48 connectors, allowing integration of legacy serial equipment into modern IP networks. - **Versatile Operation Modes:** Virtual COM, Serial Tunnel, TCP Server, TCP Client, UDP, and Modbus Gateway (Modbus TCP ↔ Modbus RTU/ASCII) for flexible communication architectures. - **High‑Speed Networking:** Four Gigabit Ethernet ports (10/100/1000Base‑T(X)) with auto MDI/MDIX and two Gigabit SFP slots (100/1000Base‑X) for fiber connectivity. - **Secure Data Transmission:** SSL data encryption with HTTPS and SSH management ensures secure remote access and protection of critical data. - **Redundant Host Support:** Simultaneous data transfer to up to **five redundant host PCs** to prevent communication loss during network or host failures. - **Advanced Event Notification:** Event warnings via **Syslog, Email, SNMP Trap, Relay Output, and Beeper** for proactive fault management. - **Industrial‑Grade Design:** Rugged metal enclosure, 15 kV ESD protection on all serial signals, and wide temperature tolerance (‑40 °C ~ 70 °C). - **Comprehensive Management Tools:** Configurable through **Web‑based GUI** and **Windows DS‑Tool utility** supporting device discovery, configuration, firmware upgrade, and monitoring. - **Linux Compatibility:** Includes fixed TTY driver for Linux systems. - **Ethernet Redundancy:** Network recovery time

Manufacturer: Oring

Category: Industrial Device Server

- **High‑Density Serial Connectivity:** 16 independent serial ports supporting RS‑232, RS‑422, and RS‑485 standards via 10‑pin RJ‑48 connectors. - **Gigabit Network Interfaces:** 4×10/100/1000Base‑T(X) RJ‑45 ports with auto MDI/MDI‑X and 2×100/1000Base‑X SFP slots for fiber uplinks, enabling flexible copper or fiber backbone integration. - **Versatile Operation Modes:** Supports Virtual COM, Serial Tunnel, TCP Server, TCP Client, UDP, and Modbus Gateway (Modbus TCP ↔ Modbus RTU/ASCII) modes for diverse communication architectures. - **Advanced Security:** SSL data encryption, HTTPS and SSH management, and secure authentication mechanisms ensure data integrity and confidentiality in critical networks. - **Redundant Host Support:** Up to 5 simultaneous host connections in Virtual COM/TCP modes and 4 IP ranges in UDP mode for redundancy and failover protection. - **Industrial‑Grade Reliability:** Wide operating temperature range (‑40 °C to 70 °C), 15 kV ESD protection on all serial signals, and metal rackmount chassis designed for harsh environments. - **Network Management & Configuration:** Web‑based GUI and Windows utility (DS‑Tool) for device discovery, configuration, firmware upgrade, and group management. - **Event Notification System:** Supports Syslog, SNMP trap, relay output, and audible beeper alerts for fault and event reporting. - **High‑Performance Data Handling:** Jumbo frame support up to 9.6 KB, throughput/latency optimization modes, and configurable data packing and delimiter settings. - **Flexible Mounting:** Standard 1U rackmount form factor with optional DIN‑rail or wall‑mount installation kits.

Manufacturer: Oring

Category: Industrial Device Server

- **Multi-Protocol Serial Connectivity:** Supports RS-232, RS-422, and RS-485 interfaces across four independent ports. - **Flexible Operation Modes:** Real COM Mode, TCP Server Mode, TCP Client Mode, and UDP Mode for diverse networking environments. - **High-Performance 32-bit CPU:** 170 MHz processor with MMU, 32 MB SDRAM, and 8 MB Flash memory for stable and efficient operation. - **Wide Power Input Range:** Accepts DC +10V to +30V, suitable for industrial power systems. - **Auto-MDIX Ethernet Port:** Automatically detects and corrects crossover or straight-through cable connections. - **High Data Rate:** Supports serial data rates from 75 bps up to 921.6 Kbps. - **Multi-Host Access:** Each serial port supports up to four simultaneous host connections in TCP Server Mode. - **Expandable Architecture:** Three external USB ports (P1, P2, P3) allow connection to Trycom expansion modules (TRP-C08S, C08U, C08H, C08X, C29U) for up to 16 serial ports or 24 digital I/O channels. - **Robust Protection:** ±15 kV ESD protection on serial interfaces; surge, over-current, and over-voltage protection on RS-422/485 lines. - **Hardware RS-485 Flow Control:** Automatic direction control ensures reliable half-duplex communication. - **Comprehensive Configuration Options:** Supports configuration via Windows Utility, Web Console, or Telnet Console. - **Security Features:** Accessible IP list for authorized host control and password protection. - **Auto IP Reporting:** Periodically reports its IP address to a designated host for network management. - **LED Indicators:** Power, Link, and TX/RX LEDs for each serial port provide real-time status monitoring. - **Mounting Flexibility:** Supports DIN rail and panel mounting. - **Factory Restore Function:** Push-button reset to restore default settings. - **Operating Temperature:** 0°C to 65°C, suitable for industrial environments. - **Compact and Durable Design:** Metal enclosure with dimensions of 145 × 118 × 26 mm and weight of approximately 728 g.

Manufacturer: Trycom

Category: Industrial Device Server

- **Multi-Protocol Serial-to-Ethernet Conversion:** Supports RS232, RS422, and RS485 interfaces with automatic direction control for RS485. - **3KV Optical Isolation:** Built-in 3KV optical isolation between serial and Ethernet interfaces to protect against ground loops and electrical surges. - **Surge, Overcurrent, and Overvoltage Protection:** Enhanced protection on RS422/485 data lines for industrial reliability. - **Multiple Operation Modes:** - **Real COM Mode** (RFC 2217 compliant) - **TCP Server Mode** - **TCP Client Mode** - **UDP Mode** - **High Performance 32-bit CPU:** 170 MHz processor with MMU, 32 MB SDRAM, and 8 MB Flash memory for stable operation. - **Wide Power Input Range:** Accepts DC +10V to +30V via screw terminal or DC jack (5.5 × 2.1 mm). - **Auto-MDIX Ethernet Port:** 10/100 Mbps auto-detecting LAN interface with automatic crossover detection and correction. - **Multi-Host Connectivity:** Supports up to 4 simultaneous host connections per port in TCP Server or TCP Client mode. - **Web, Telnet, and Windows Configuration:** Configurable via Web Console, Telnet Console, or Windows-based Serial Server Admin Utility. - **Virtual COM Port Drivers:** Compatible with Windows XP, Vista, 2000, 2003/2008 Server, and Windows 7 (32-bit and 64-bit). - **Security and Management Features:** - Accessible IP list for authorized host control - Auto IP Address Reporting - Auto Warning via Email or SNMP Trap - Password protection and factory reset button - **LED Indicators:** Power, Link, and dual TX/RX indicators for RS232 and RS422/485 ports. - **Mounting Options:** DIN rail or panel mounting supported. - **Standalone Operation:** No external host required for operation once configured.

Manufacturer: Trycom

Category: Industrial Device Server