- **High-Speed Digital I/O:** 32 digital input and 32 digital output channels, all TTL-compatible, optimized for high-speed data acquisition and pattern generation. - **PCI Express® Interface:** Utilizes a single-lane (x1) PCI Express interface for high bandwidth and low latency communication with host systems. - **High Data Throughput:** Achieves up to 12 MB/s transfer rate using external 3 MHz clock or handshaking mode; 8 MB/s with internal 2 MHz timer pacer. - **Bus-Mastering DMA:** Supports direct memory access for both input and output operations, minimizing CPU load and maximizing throughput. - **Multiple Transfer Modes:** - Programmed I/O - Timer pacer mode (internal clock) - External clock mode - Handshaking mode (REQ/ACK signals) - **Programmable Timer/Counter:** Integrated 82C54-10 programmable counter with 4 MHz base clock for precise timing control of digital I/O operations. - **Interrupt Support:** Multiple programmable interrupt sources including EO_ACK, EI_REQ, and timers 0–2. - **Plug and Play Configuration:** Fully compliant with PCI Express Plug and Play standards; no jumper or DIP switch settings required. - **Software Support:** Compatible with Windows (XP, 2000, 2003, Vista, 7) and Linux. Supported by ADLINK’s DAQPilot, DAQBench, and legacy PCIS-DASK drivers. Integration available for LabVIEW™, MATLAB®, and .NET environments. - **Compact Design:** Half-size PCB (148 mm x 102 mm) suitable for space-constrained systems.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCIe

**Digital I/O Capabilities** - 48-channel TTL/DTL-compatible digital I/O lines. - Emulates two industry-standard Intel 8255 Programmable Peripheral Interface (PPI) chips operating in Mode 0. - Buffered circuits for enhanced driving capability and signal integrity. - Direct interface with OPTO-22-compatible I/O modules for industrial-grade isolation and signal conditioning. - Output status read-back capability for verification and monitoring. **Timer/Counter and Interrupt System** - Integrated 8254 programmable timer/counter chip with three 16-bit counters. - 32-bit cascaded timer for watchdog or periodic interrupt generation. - 16-bit event counter for external event counting or frequency measurement. - Programmable interrupt source selection with dual interrupt architecture (INT1 and INT2). - Supports event-triggered and timer-triggered interrupts. **Power and Protection** - Provides +12V and +5V auxiliary power outputs on OPTO-22 connectors. - Resettable fuses protect external devices from overcurrent or short-circuit conditions. - Onboard watchdog timer and event counter for system reliability. **Software and Driver Support** - Comprehensive driver support for Windows and Linux platforms. - Compatible with ADLINK’s PCIS-DASK, PCIS-DASK/X, and PCIS-LVIEW software libraries. - Supports programming in C/C++, Visual Basic, Delphi, and LabVIEW environments. - Includes ActiveX and OPC server support for SCADA and HMI integration. **Plug-and-Play Configuration** - Fully compliant with PCI Express Plug-and-Play specifications. - Automatic resource allocation for I/O addresses and interrupts by system BIOS. - No manual jumper or DIP switch configuration required.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCIe

- **High-Density Digital I/O:** 96-channel TTL/DTL-compatible digital input/output lines, organized as four 24-bit ports (A, B, C per connector). - **8255 PPI Emulation:** Emulates four industry-standard Intel 8255 Programmable Peripheral Interface chips operating in Mode 0 configuration. - **Opto-22 Compatibility:** Direct interface with OPTO-22-compatible I/O modules for industrial control and signal isolation. - **Buffered I/O Circuits:** Buffered input/output circuitry ensures higher drive capability and signal integrity. - **Dual Interrupt System:** Supports two simultaneous interrupt sources (INT1 and INT2) with programmable trigger conditions and multiplexed interrupt control. - **Integrated Timer/Counter:** Includes one 8254 programmable timer/counter chip providing: - 32-bit cascaded timer for watchdog or periodic interrupts - 16-bit event counter for external event counting - Programmable interrupt generation - **Power Distribution:** Provides +5V and +12V power outputs on OPTO-22 connectors with resettable fuses for external device protection. - **Plug-and-Play PCI Express Interface:** Fully compliant with PCI Express x1 bus standard; automatic resource allocation (I/O address and IRQ) via BIOS. - **Software Support:** Comprehensive driver and library support for Windows and Linux, including PCIS-DASK, LabVIEW™, MATLAB®, and ActiveX/DAQBench™. - **Industrial-Grade Design:** Operating temperature range 0°C to 60°C, humidity 5–95% non-condensing, suitable for industrial automation environments.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCIe

- **High-Speed PCI Express Interface:** PCIe x1 lane interface providing up to 80 MB/s sustained data transfer rate via bus mastering DMA. - **Flexible Channel Configuration:** 32 channels of 5 V TTL-compatible digital I/O, configurable as 16 inputs and 16 outputs, or as 32 inputs or 32 outputs. - **High Throughput:** - Up to 80 MB/s sustained transfer rate (32-bit @ 20 MHz). - Up to 160 MB/s burst rate for digital input using external 40 MHz clock. - **Large Onboard FIFO Buffers:** 64 KB total FIFO memory (32 KB for input, 32 KB for output) for high-speed buffered data transfer. - **Advanced DMA Support:** Bus mastering DMA with scatter-gather capability for efficient, non-contiguous memory transfers and ring-buffer operation. - **Programmable Timing and Triggering:** - Onboard 8254 programmable timer/counter with 10 MHz base clock. - Independent DI_TRG and DO_TRG trigger signals for acquisition and pattern generation. - Internal or external clocking up to 40 MHz. - **Auxiliary I/O:** 4 auxiliary digital inputs and 4 auxiliary digital outputs for control or status signaling. - **Active Termination:** Software-selectable active terminators for reliable high-speed and long-distance data transmission. - **Software and OS Support:** - Windows 7/Vista/XP/2000/2003 Server - Linux (PCIS-DASK/X) - Supported APIs: DAQPilot for LabVIEW™, PCIS-DASK, DAQBench, and AD-Logger. - Programming languages: VB.NET, VC.NET, C/C++, Delphi, Borland C++ Builder. - **Plug and Play Configuration:** Fully compliant with PCI Plug and Play standards; no jumpers or DIP switches required.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCIe

- **High‑Speed PCI Express® Interface:** - x1 lane PCI Express® interface delivering up to **200 MB/s** maximum throughput. - Bus‑mastering DMA with scatter‑gather support for efficient, CPU‑independent data transfer. - **Flexible Clocking Architecture:** - Internal clock up to **50 MHz** (programmable divider 100 MHz/N, 2 ≤ N ≤ 65,535). - External clock up to **100 MHz** (supports 8/16‑bit data width). - **16‑step phase shift** (22.5° increments) for precise timing alignment. - **Programmable Logic Levels:** - Software‑selectable logic levels: **1.8 V**, **2.5 V**, or **3.3 V** (5 V compatible). - Uniform logic level applied across all I/O groups. - **Configurable I/O Direction:** - 32 bi‑directional channels divided into four 8‑bit groups (A–D). - Each group independently configurable as input or output. - **Advanced Triggering and Handshaking:** - Supports **software**, **external digital**, **pattern match**, **post/re‑trigger**, and **gated** trigger modes. - Flexible handshaking (DI‑REQ/DI‑ACK, DO‑REQ/DO‑ACK) and burst handshaking for reliable data exchange. - **Auxiliary Function I/O (AFI):** - 8 programmable AFI channels configurable for I²C, SPI, trigger, event, or clock I/O. - I²C master (up to 244 kHz) and SPI master (up to 62.5 MHz) support. - **High‑Speed Data Integrity:** - 8 K‑sample FIFO buffers for both input and output. - Scatter‑gather DMA ensures continuous, loss‑free data streaming. - **Software and OS Support:** - Compatible with Windows 2000/XP/Vista/2003. - Supported programming environments: VB.NET, VC.NET, Delphi, BCB, DAQBench. - Driver package: **PCIS‑DASK** for Windows.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCIe

- **High-Speed PCI Express Interface:** Utilizes a PCI Express x4 lane interface providing up to 400 MB/s throughput. - **Flexible Channel Configuration:** 32 bi-directional digital I/O channels divided into four 8-bit groups, each configurable as input or output. - **Selectable Logic Levels:** Software-selectable voltage levels of 1.8 V, 2.5 V, or 3.3 V (5 V compatible) for all I/O lines. - **High Clock Rates:** - Internal clock up to 100 MHz - External clock up to 200 MHz (DI mode, 8/16-bit width) - **Phase Shift Control:** 80-step phase shifting (4.5° per step) for precise timing alignment in external clock mode. - **Integrated Serial Interfaces:** Built-in I²C and SPI master interfaces for direct communication with peripheral devices. - **DMA and FIFO Architecture:** Scatter-gather bus-mastering DMA with 8K-sample DI FIFO and 20K-sample DO FIFO ensures continuous high-speed data transfer without CPU overhead. - **Trigger and Handshake Support:** Multiple trigger modes (post, gated, re-trigger) and handshake protocols for synchronized data exchange. - **Auxiliary Function I/O (AFI):** Eight programmable AFI lines supporting static I/O, triggers, handshake, and clock I/O. - **Software Compatibility:** Supports Windows XP/7/8 (x86/x64) and Linux; compatible with LabVIEW®, MATLAB®, and Visual Studio .NET.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCIe

- **48 Digital I/O Channels:** Provides a total of 48 programmable digital input/output lines for versatile signal interfacing. - **8255 Mode 0 Compatibility:** Fully compatible with the Intel 8255 Programmable Peripheral Interface (PPI) in Mode 0 operation, ensuring seamless integration with existing software and hardware architectures. - **PCI Bus Interface:** Designed for standard PCI bus systems, supporting automatic resource allocation through Plug and Play functionality. - **Plug and Play Configuration:** No manual jumper or DIP switch settings required; the system automatically assigns I/O addresses and IRQs. - **Dual 50-pin Flat Cable Connectors:** Equipped with two 50-pin headers for easy connection to external devices, terminal boards, or signal conditioning modules. - **Compact PCB Design:** Dimensions of 174 mm (L) × 106 mm (H) allow installation in standard PCI slots without interference. - **Industrial-Grade Reliability:** Built with high-quality components for stable operation in industrial environments. - **Flexible I/O Direction Control:** Each 24-bit port group can be configured independently as input or output. - **Software Compatibility:** Supports a wide range of operating systems and development environments through standard driver interfaces. - **Ideal for Automation and Control:** Suitable for digital signal monitoring, machine control, process automation, and laboratory instrumentation.

Manufacturer: Axiom

Category: DIO Non-Isolated PCI

- **Expansion for AX5234P:** The AX5234A serves as an extension module that doubles the available I/O channels of the AX5234P board, increasing the total number of digital I/O lines from 96 to 192 bits. - **High-Density Digital I/O:** Provides multiple 8-bit ports (Ports A, B, and C) grouped into sets, allowing flexible configuration for input or output operations. - **TTL/DTL Compatibility:** Fully compatible with TTL (Transistor-Transistor Logic) and DTL (Diode-Transistor Logic) signal levels, ensuring broad interoperability with industrial sensors, actuators, and control systems. - **Improved Noise Immunity:** Incorporates hysteresis with a typical threshold difference (VT+ - VT−) of 0.4V, enhancing noise margin and signal stability in electrically noisy environments. - **Plug-and-Play PCI Interface:** Works seamlessly with the AX5234P’s PCI bus interface, supporting automatic address and interrupt configuration. - **Flexible Connectivity:** Equipped with multiple 50-pin headers for easy connection to external devices via ribbon or twisted-pair cables. - **Software Support:** Compatible with multiple programming environments including Microsoft C, QuickBasic, Turbo C, and Turbo Pascal, with sample code and drivers provided. - **Industrial Reliability:** Designed for continuous operation in industrial environments with wide temperature and humidity tolerance.

Manufacturer: Axiom

Category: DIO Non-Isolated PCI

- **96 Digital I/O Lines:** Provides 96 TTL-compatible digital input/output channels organized into 12 ports (A, B, C per group). - **8255 Mode 0 Compatibility:** Fully compatible with the Intel 8255 programmable peripheral interface standard, ensuring broad software and hardware compatibility. - **Plug and Play PCI Interface:** Automatically configured by the system BIOS without manual jumper or DIP switch settings. - **High Noise Immunity:** Improved noise margins with hysteresis (VT+ - VT− = 0.4V typical) for stable signal detection in industrial environments. - **Flexible I/O Configuration:** Each port can be independently programmed as input or output. - **Multiple Connectors:** Equipped with three 50-pin flat cable connectors for external signal interfacing. - **Compact Form Factor:** Board dimensions of 175 mm × 106 mm allow installation in standard PCI slots. - **Wide Operating Range:** Designed for 0°C to 60°C operation and up to 90% non-condensing relative humidity. - **Software Support:** Includes device drivers and example programs for Turbo C, Turbo Pascal, and Microsoft QuickBasic 4.5. - **Expansion Capability:** Compatible with AX5234A extension board for up to 192-bit I/O expansion.

Manufacturer: Axiom

Category: DIO Non-Isolated PCI

- **High‑Speed Digital I/O:** 32 TTL‑compatible digital inputs and 32 TTL‑compatible digital outputs. Maximum transfer rate up to **12 MB/s** using bus‑mastering DMA. - **Universal PCI Compatibility:** Supports both **3.3 V and 5 V PCI signaling**, ensuring broad system compatibility. - **Low‑Profile Design:** Compact MD1 form factor (168 mm × 64 mm) ideal for small chassis and embedded PCs. - **Multiple Data Transfer Modes:** - Direct programmed I/O control - Internal timer pacer control - External clock mode - Handshaking mode (REQ/ACK) - **Bus‑Mastering DMA:** Enables high‑throughput, low‑latency data transfer without CPU overhead. - **Programmable Counter/Timer:** Integrated 82C54‑10 programmable interval timer with 4 MHz base clock for pacer generation and timing control. - **FIFO Buffers:** 32‑word (DWord) FIFO for both input and output channels to ensure smooth high‑speed data streaming. - **Isolation and Protection:** 16/16 isolated channels with 2.5 kV isolation protection (for specific configurations). - **Interrupt Support:** Multiple interrupt sources selectable by software (EO_ACK, EI_REQ, Timer 0/1/2). - **Software Support:** Comprehensive driver and library support for Windows and Linux, including PCIS‑DASK, LabVIEW®, HP‑VEE™, DASYLab™, InTouch™, ISaGRAF™, and OPC Server integration. - **Certifications:** CE and FCC Class A compliant for EMC/EMI performance.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCI

- **High-Speed Digital I/O:** 32 digital input and 32 digital output channels, TTL-compatible, optimized for high-speed data transfer and pattern generation. - **High Data Throughput:** Up to **12 MB/s** transfer rate using bus-mastering DMA via 32-bit PCI bus architecture. - **Multiple Transfer Modes:** Supports **programmed I/O**, **interrupt-driven I/O**, **bus-mastering DMA**, **timer pacer control**, **external clock mode**, and **handshaking mode**. - **Programmable Timer/Counter:** Integrated **82C54-10 programmable counter** with a 4 MHz base clock for generating pacer signals and timing control. - **Flexible Triggering and Handshaking:** Supports **I_REQ/I_ACK** and **O_REQ/O_ACK** signals for synchronized data transfer with external devices. - **FIFO Buffers:** Onboard **32-word FIFO** for both input and output (PCI-7200/LPCI-7200S) and **2K + 8-word FIFO** for cPCI-7200 input channels. - **Bus-Mastering DMA:** Enables direct memory access for high-speed, low-latency data transfer without CPU intervention. - **Software-Selectable Interrupt Sources:** Multiple interrupt sources including EO_ACK, EI_REQ, Timer 0, Timer 1, and Timer 2. - **Cross-Platform Software Support:** Compatible with **Windows 7/Vista/XP/2000/2003** and **Linux**. Supported by **DAQPilot**, **DAQBench**, **LabVIEW™**, **MATLAB®**, and **PCIS-DASK** drivers. - **Compact Design:** Half-size PCI card (148 mm x 102 mm) suitable for space-constrained systems. - **Plug and Play Configuration:** Fully compliant with PCI Plug and Play standards; no jumper or DIP switch configuration required.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCI

- **24-Channel Digital I/O:** Provides 24 TTL/DTL-compatible digital input/output lines organized as three 8-bit ports (Port A, Port B, Port C). - **Opto-22 Compatibility:** Fully compatible with industry-standard Opto-22 I/O modules and termination boards, allowing direct connection to external relay, input, and output modules. - **8255 PPI Emulation:** Emulates Mode 0 of the Intel 8255 PPI, enabling flexible configuration of ports as input or output. - **Programmable Interrupt System:** Supports multiple interrupt sources, including digital input lines and timer outputs, with dual interrupt capability. - **Integrated Timer/Counter:** Includes one 16-bit event counter and one 32-bit cascaded timer for event counting and timed interrupt generation. - **Buffered I/O Circuits:** Provides high drive capability and signal buffering for reliable operation in industrial environments. - **Power Output Protection:** Onboard resettable fuses protect the +5V and +12V power outputs available on the Opto-22 connector. - **Software Compatibility:** Supported by ADLINK’s PCIS-DASK driver library for Windows and Linux, as well as LabVIEW™, MATLAB®, and HP VEE™ integration. - **Plug and Play PCI Interface:** Fully compliant with PCI 2.1 specifications, supporting automatic resource allocation (I/O address and IRQ).

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCI

- **48-Channel Digital I/O:** Provides 48 TTL/DTL-compatible digital input/output lines organized into two 24-bit groups. - **Opto-22 Compatibility:** Fully compatible with Opto-22 standard external I/O modules and termination boards. - **8255 PPI Emulation:** Emulates two Intel 8255 Programmable Peripheral Interface chips operating in Mode 0 configuration. - **Buffered I/O Circuits:** Ensures higher driving capability and signal integrity for industrial environments. - **Programmable Timer/Counter:** Includes one 16-bit event counter and one 32-bit cascaded timer for interrupt generation and event counting. - **Dual Interrupt System:** Supports two independent interrupt sources (INT1 and INT2) selectable from digital inputs or timer outputs. - **Plug and Play PCI Interface:** Automatic resource allocation for IRQ and I/O addresses via PCI BIOS; no manual jumper configuration required. - **Power Output Protection:** Provides +5V and +12V outputs on the Opto-22 connectors with resettable fuses for external device protection. - **Software Support:** Includes C/C++ libraries, Windows DLLs, and drivers for multiple operating systems (DOS, Windows 95/98/NT/2000, Linux). - **High Data Transfer Rate:** Supports up to 500 Kbytes/s typical transfer rate. - **Industrial Reliability:** Designed for 0°C to 60°C operation and 5–95% non-condensing humidity environments.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCI

- **High-Density Digital I/O:** 96 TTL/DTL-compatible digital I/O channels organized as four 24-bit ports (Port A, B, C per PPI). - **Opto-22 Compatibility:** Fully compatible with Opto-22 standard 50-pin connectors, allowing direct connection to Opto-22 I/O modules and termination boards. - **8255 PPI Emulation:** Emulates four industry-standard 8255 PPI chips in Mode 0 configuration, providing 24 I/O lines per chip. - **Buffered I/O Circuits:** Buffered input/output circuitry ensures higher driving capability and signal integrity. - **Programmable Timer/Counter:** Includes one 16-bit event counter and a cascaded 32-bit timer for interrupt generation and event counting. - **Dual Interrupt System:** Supports two independent interrupt sources (INT1 and INT2) selectable from DIO channels or timer outputs. - **Power Output Protection:** Provides +5V and +12V outputs on Opto-22 connectors with resettable fuses for external device protection. - **Plug and Play PCI Interface:** Fully compliant with PCI Plug and Play specifications; no manual configuration of IRQ or I/O address required. - **Software Support:** Comprehensive driver and library support for DOS, Windows 95/98/NT/2000, and Linux (via PCIS-DASK/X). Compatible with LabVIEW®, HP VEE™, DASYLab™, InTouch™, ISaGRAF™, and OPC systems. - **Output Status Readback:** Allows software to verify output states for reliable control feedback.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCI

- **High-Speed Data Transfer:** - Sustained data throughput up to **80 MB/s** via 32-bit PCI bus mastering DMA. - Maximum internal transfer rate of **160 MB/s** for digital input using external 40 MHz clock. - **Flexible I/O Configuration:** - **32 software-configurable channels** supporting 16 DI/16 DO, 32 DI, or 32 DO modes. - Two 16-bit ports (PORTA and PORTB) configurable independently as input or output. - **Advanced DMA Architecture:** - **Bus-mastering DMA** for processor-free data transfer. - **Scatter/Gather DMA** for non-contiguous memory access and large data streaming. - Supports **chaining mode** for continuous or circular buffer operation. - **FIFO Buffering:** - Dual **16K-word FIFOs** (input and output) for high-speed buffering. - Programmable almost-empty/full thresholds. - **Clocking and Triggering:** - Internal clock sources: 20 MHz, 10 MHz, or programmable timer (82C54). - External clock input up to 40 MHz. - Independent **trigger inputs (DI_TRG, DO_TRG)** for acquisition and pattern generation. - Supports **handshaking** and **burst handshaking** modes for reliable data exchange. - **Programmable Counter/Timer:** - Onboard **Intel 8254-compatible 3-channel timer** with 10 MHz base clock. - Timer #0 for DI pacing, Timer #1 for DO pacing, Timer #2 for interrupt generation. - **Auxiliary I/O:** - 4 auxiliary digital inputs and 4 auxiliary digital outputs (TTL-compatible). - Useful for control, status, or synchronization signals. - **Active Termination:** - Software-selectable **active terminators** (111 Ω, 2.9 V) for long-distance, high-speed signal integrity. - **Software & OS Support:** - Drivers for **Windows 7/Vista/XP/2000/2003 Server** and **Linux**. - Compatible with **LabVIEW™, DAQBench™, VB.NET, VC++, Delphi, and BCB**. - ADLINK **PCIS-DASK** and **DAQPilot** driver libraries included. - **Plug & Play PCI Configuration:** - Fully compliant with PCI Plug-and-Play resource allocation. - No jumpers or DIP switches required.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCI

- **48 TTL-Compatible Digital I/O Channels:** Provides 48 bidirectional digital lines configurable as input or output in 8-bit port groups. - **High Current Drive Capability:** Each output channel can source up to 15 mA and sink up to 48 mA, suitable for driving LEDs, relays, and other TTL/CMOS devices. - **Change-of-State (COS) Interrupt:** Generates an interrupt when any input bit changes state, enabling event-driven digital monitoring. - **Dual Interrupt System:** Two independent interrupt sources (INT1 and INT2) allow simultaneous handling of multiple event types such as COS, timer, or counter events. - **Output Status Readback:** Supports readback of output states for verification and closed-loop control. - **External Trigger Input:** Accepts an external trigger signal (EXTTRG, pin 99) to latch input data synchronously with external events. - **Programmable Timer/Counter:** Includes one 8254 programmable timer/counter chip providing a 32-bit timer and a 16-bit event counter for timing and counting applications. - **User-Configurable Power-On State:** Each port can be configured via jumpers to power up in a pulled-high, pulled-low, or floating state. - **Onboard Power Outputs:** Provides +5 V and +12 V outputs on the SCSI connector (protected by resettable fuses) for powering external circuits. - **Watchdog Timer:** 32-bit watchdog timer ensures system reliability and can reset outputs or trigger interrupts on timeout. - **Compact PCI Form Factor:** Half-size PCI card (158 mm × 107 mm) compliant with PCI Bus Rev. 2.1.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCI

- **High Channel Density:** 96 TTL-compatible digital I/O channels (12 ports of 8 bits each). - **High Current Drive Capability:** Each output channel can source up to 15 mA and sink up to 48 mA, suitable for driving LEDs, relays, and other loads. - **Output Readback:** Supports real-time output status readback for verification and monitoring. - **Change-of-State (COS) Interrupt:** Generates interrupts when any input bit changes state, enabling event-driven control. - **Dual Interrupt System:** Two independent interrupt sources (INT1 and INT2) for flexible event handling. - **Programmable Timer/Counter:** Includes one 8254 programmable timer/counter chip providing a 32-bit cascaded timer and a 16-bit event counter. - **External Trigger Input:** Allows external signals to latch input data or trigger events. - **User-Configurable Power-On State:** Each port can be configured via jumpers to power up in pull-high, pull-low, or floating state. - **Watchdog Timer:** 32-bit programmable timer for system monitoring and fail-safe operation. - **High-Speed Data Transfer:** Supports up to 1 MB/s typical transfer rate via programmed I/O. - **Comprehensive Software Support:** Compatible with ADLINK’s PCIS-DASK driver library, LabVIEW®, HP-VEE™, DASYLab™, InTouch™, InControl™, ISaGRAF™, and OPC Server. - **Compact Form Factor:** Half-size PCI card (158 mm × 107 mm). - **Industrial Reliability:** Operating temperature range of 0°C to 60°C and humidity tolerance up to 95% non-condensing.

Manufacturer: Adlink Technology Inc.

Category: DIO Non-Isolated PCI

- **Dual‑format PCI support:** Compatible with both Low Profile PCI and standard PCI slots using the supplied interchangeable bracket. - **32‑bit, 33 MHz PCI bus interface:** Universal key shape supports both 3.3 V and 5 V signaling environments. - **16 digital input channels:** TTL‑level, negative logic inputs with 10 kΩ pull‑up resistance. - **16 digital output channels:** Open‑collector outputs (negative logic) rated at 30 V DC, 40 mA per channel maximum. - **Interrupt capability:** All 16 input channels can be configured as interrupt sources; selectable rising or falling edge trigger. - **Digital noise filter:** Programmable digital filter prevents false triggering due to noise or contact bounce. - **Fast response:** Typical response time within 200 ns (variable with pull‑up resistance). - **Software support:** - **Windows:** API‑PAC(W32) driver library (Win32 API‑based DLLs). - **Linux:** API‑DIO(LNX) driver package. - **LabVIEW:** VI‑DAQ library for National Instruments LabVIEW. - **Diagnostic and sample tools:** Includes API‑TOOL configuration utility and diagnostic program for hardware verification. - **Compact design:** 121.69 mm (L) × 63.41 mm (H), weight 60 g. - **RoHS, CE, and VCCI compliant.**

Manufacturer: Contec

Category: DIO Non-Isolated PCI

- **Digital I/O Configuration:** - 16 TTL-level digital inputs - 16 open-collector digital outputs (negative logic) - All input channels can be configured as interrupt sources - **Logic Level:** - TTL (5VDC, negative logic) - Compatible with standard 5V TTL devices - **Interrupt Functionality:** - Four interrupt input signals combined into one interrupt request (INTA#) - Software-configurable interrupt trigger edge (rising or falling) - **High-Speed Operation:** - Input response time: 200 nanoseconds (max) - Output switching time: 1 microsecond (typical) - **Output Drive Capability:** - Open collector outputs capable of sinking up to 40 mA per channel - Maximum output voltage: 30VDC - **Input Characteristics:** - Input resistance: 10 kΩ (pull-up) - Input current: 5VDC, 6.4 mA typical - **Compact PCI Form Factor:** - Short-size PCI board (121.69 mm × 106.68 mm × 19 mm) - Occupies one PCI slot - **Connector Type:** - 37-pin female D-sub (D-type) connector (JAE DCL-J37SAF-20L9 or equivalent) - **Software Support:** - Windows and Linux drivers (API-TOOL) - LabVIEW VI-DAQ library for National Instruments LabVIEW integration - License-free development and runtime drivers - **Compatibility:** - Fully compliant with PCI Local Bus Specification Revision 2.2 - Supports both 5V and 3.3V PCI signaling environments

Manufacturer: Contec

Category: DIO Non-Isolated PCI

- **16 TTL Inputs / 16 Open-Collector Outputs:** Provides 16 unisolated TTL-level input channels and 16 unisolated open-collector output channels. Each channel supports a response time of 200 nanoseconds, enabling high-speed digital signal processing. - **Interrupt Capability on All Inputs:** All 16 input channels can be configured as interrupt request signals. Interrupts can be enabled or disabled per bit, and the triggering edge (rising or falling) can be selected via software. - **Digital Noise Filter:** A software-configurable digital filter prevents false signal recognition due to noise or contact chattering. Filter time constants are adjustable from 0.25 µs to 131.072 ms. - **Driver and Software Support:** Includes Windows and Linux driver libraries (API-PAC(W32), API-DIO(WDM), API-DIO(98/PC), API-DIO(LNX)) and diagnostic utilities. Compatible with Visual Basic, Visual C++, C#, Delphi, and gcc. - **LabVIEW Integration:** Supported by CONTEC’s VI-DAQ library, enabling seamless integration with National Instruments LabVIEW for data acquisition and control applications. - **PCI Bus Compatibility:** Fully compliant with 32-bit, 33 MHz PCI bus specifications. Supports both 3.3V and 5V universal key slots. - **Backward Compatibility:** Connector pin assignments and functions are compatible with the earlier PIO-16/16T(PCI) model, simplifying system upgrades. - **Compact and Lightweight Design:** Dimensions of 121.69 mm (L) × 105.68 mm (H) and a weight of approximately 100 g. - **Regulatory Compliance:** Certified for RoHS, CE, and VCCI standards.

Manufacturer: Contec

Category: DIO Non-Isolated PCI

- **64 total I/O channels:** 32 TTL-level inputs and 32 open-collector outputs. - **High-speed response:** Input response time of 200 nanoseconds (typical). - **Negative logic operation:** Inputs and outputs operate on TTL-level negative logic. - **Interrupt capability:** Four input signals (I00–I03) can generate interrupt requests; combined into one INTA line. - **Digital filter function:** Programmable digital filter for input channels to suppress noise and contact chattering. - **Handshake function:** STB/ACK handshake control for input channels 0–15. - **Output data monitoring:** Output states can be read back without affecting output conditions. - **Bit and group I/O operations:** Supports bit-level and group-level input/output addressing. - **Compact PCI short-size form factor:** 121.69 mm (L) × 107.0 mm (H) × 18.5 mm (D). - **Plug & Play configuration:** Automatic resource allocation (I/O address and IRQ) by the PCI BIOS. - **Multiple board support:** Up to 16 boards can be installed in a single system. - **Software support:** Drivers for Windows and Linux, plus LabVIEW VI-DAQ library. - **API compatibility:** Supports CONTEC’s API-PAC(W32) and API-TOOL libraries for application development.

Manufacturer: Contec

Category: DIO Non-Isolated PCI

- **Unisolated 32-Channel TTL Inputs and 32-Channel Open-Collector Outputs:** Provides 32 input channels (negative logic, TTL level, 10 kΩ pull-up) and 32 output channels (open collector, max. 30 VDC, 40 mA per channel). Both input and output circuits operate with a response time of 200 ns or less. - **Full Interrupt Capability:** All 32 input channels can be configured as interrupt request sources. Interrupts can be enabled or disabled per bit, and the triggering edge (rising or falling) can be selected individually. - **Digital Input Filtering:** A software-configurable digital filter prevents false triggering due to noise or contact chattering. Filter time constants are adjustable via software from 0 s to 131.072 ms. - **High-Speed PCI Bus Interface:** Compliant with 32-bit, 33 MHz PCI bus specifications, supporting both 3.3 V and 5 V universal key slots. The board draws power from the +5 V PCI rail. - **Comprehensive Software Support:** Includes Windows and Linux driver libraries (API-PAC(W32)), diagnostic utilities, and sample programs. Compatible with Visual Basic, Visual C++, C#, Delphi, and gcc. - **LabVIEW Integration:** Supported by CONTEC’s VI-DAQ library, enabling seamless integration with National Instruments LabVIEW for data acquisition and control applications. - **Compact and Lightweight Design:** Board dimensions are 121.69 mm (L) × 105.68 mm (H), with a weight of approximately 100 g. - **RoHS, CE, and VCCI Certified:** Meets international environmental and electromagnetic compliance standards.

Manufacturer: Contec

Category: DIO Non-Isolated PCI

- **High‑Speed Bus Mastering:** Supports PCI bus master DMA transfer at up to 80 MB/s, enabling direct memory access between the board and PC memory without CPU overhead. - **Flexible I/O Configuration:** 32 TTL‑level digital channels configurable as 32‑bit input, 32‑bit output, or 16‑bit input + 16‑bit output. - **High‑Frequency Pattern I/O:** Capable of 20 MHz sampling (input) and 20 MHz pattern generation (output). - **On‑Board FIFO Buffers:** 1 K‑word FIFO memory per channel (input and output) ensures stable high‑speed data flow. - **Synchronization Control (SC) Connectors:** Enables inter‑board synchronization for up to 16 boards, allowing simultaneous operation across multiple channels or systems. - **Interrupt and Timer Functions:** Four input lines (DIOA00–DIOA03) can generate software‑controlled interrupts on rising edges. An integrated timer provides precise timing even under Windows OS. - **Bus Mastering Control Signals:** Includes REQ/ACK handshake lines and external start/stop/clock inputs for precise control of pattern I/O. - **Software Support:** Bundled with CONTEC’s API‑PAC(W32) driver library for Windows and API‑DIO(LNX) for Linux, supporting Visual C/C++, Visual Basic, Delphi, Builder, gcc, and Kylix. - **General‑Purpose I/O Mode:** Can function as a standard digital I/O board when bus mastering is not required. - **Compact PCI Form Factor:** Standard PCI 32‑bit, 33 MHz interface with universal keying for both 3.3 V and 5 V slots.

Manufacturer: Contec

Category: DIO Non-Isolated PCI

- **48-Channel Bi-Directional Digital I/O:** Provides 48 unisolated TTL-level I/O channels, configurable as input or output in 8-bit units (4-bit units for certain ports). Compatible with the functional equivalent of Intel i8255 Mode 0 operation. - **High-Speed Response:** Achieves a response time of **200 nanoseconds**, enabling fast digital signal processing suitable for real-time control systems. - **Interrupt Functionality:** All 48 input channels can be used as interrupt inputs. Interrupts can be enabled or disabled per bit, and the triggering edge (rising or falling) can be selected individually. - **Digital Noise Filter:** Integrated digital filter function prevents false signal recognition caused by noise or contact chattering. Filter parameters are software-configurable. - **Driver and Software Support:** Bundled with **API-PAC(W32)** driver library supporting both **Windows** and **Linux** environments. Includes **API-DIO(WDM)** and **API-DIO(98/PC)** for Windows, and **API-DIO(LNX)** for Linux. Compatible with **LabVIEW** via the **VI-DAQ** library for seamless integration with National Instruments environments. - **Connector Compatibility:** Uses a 68-pin 0.8mm pitch female connector (HDRA-F68LFDT+ by Honda Tsushin Kogyo or equivalent). Connector and pin assignments are compatible with CONTEC’s CardBus model **PIO-48D(CB)H** and PCI model **PIO-48D(PCI)**, simplifying system migration. - **Dual Bracket Support:** Supplied with interchangeable brackets for both **Low Profile** and **Standard PCI** slots. - **RoHS, CE, and VCCI Certified:** Complies with major environmental and electromagnetic compatibility standards.

Manufacturer: Contec

Category: DIO Non-Isolated PCI

- **48 Bi-Directional TTL Channels:** Provides 48 channels configurable as input or output, supporting positive logic TTL-level signals. - **8255 Mode 0 Compatibility:** Fully emulates the Intel 8255 PPI Mode 0 operation, ensuring compatibility with legacy systems and software. - **High-Speed Response:** Achieves a maximum response time of 200 nanoseconds, suitable for high-frequency digital signal processing. - **Interrupt Capability:** All 48 input signals can generate interrupt requests, allowing event-driven control and monitoring. - **Non-Isolated Design:** Direct TTL-level interfacing for maximum speed and minimal latency, ideal for short-distance, low-noise environments. - **PCI Bus Interface:** Compliant with 32-bit, 33 MHz PCI bus (5V signaling), ensuring plug-and-play installation and automatic resource allocation. - **Compact Form Factor:** Short-size PCI board (176.41 mm × 106.68 mm) suitable for standard desktop or industrial PCs. - **Software Support:** Includes Windows and Linux drivers (API-TOOL), and LabVIEW VI-DAQ library for seamless integration with development environments. - **Flexible Connectivity:** Equipped with one 96-pin half-pitch connector for external I/O and two 50-pin mini-ribbon connectors for expansion or signal routing. - **High Current Drive Capability:** Supports output drive of up to 24 mA (sink) and -15 mA (source) per channel. - **Comprehensive Accessory Support:** Compatible with CONTEC’s range of terminal blocks, cables, and connector accessories for easy wiring and system integration.

Manufacturer: Contec

Category: DIO Non-Isolated PCI